News

Forklift Chassis Resistance Inspection and Maintenance Jul 17 , 2023

Rough Terrain Forklift chassis resistance inspection and maintenance 1. Chassis resistance inspection. The resistance of any part between the forklift wiring and the chassis should be at least 1000 ohms. Many failures are caused by chassis short circuits. Usually, there are two faults before a fault occurs. However, since the battery can have chassis leaks, even a single short in the forklift wiri...

How to adjust the height of forklift fork and mast Jul 05 , 2023

How to adjust the height of counterbalanced diesel forklift fork and mast 1. Move the mast so that the rear is fully tilted. 2. Completely lower the fork. Bottom yoke bearings, forklift bearings. 3. For the full free lift and full free triple lift models, the bottom of the inner mast must be as high as the bottom of the fixed mast. 4. Measure the distance from the bottom of the inner column to the...

How to remove the forklift counterweight and instrument frame? Jun 15 , 2023

How to remove the diesel rough terrain forklift counterweight and instrument frame? 1. Counterweight. 1. Remove the battery cover of the forklift. 2. Remove the top protection frame assembly. 3. Remove the forklift battery from the forklift. 4. Open the counterweight cover, lift the center of gravity, and then remove the counterweight cover. 5. Remove the wiring and cables connected to t...

Disassembly and decomposition steps of forklift oil pump Jun 09 , 2023

Disassembly and decomposition steps of 3 tons diesel forklift oil pump 1. Disassembly steps. 1. Remove the lower cover, and clean and remove dust around the oil pump. 2. Cut off the oil inlet hose and drain the oil in the oil pump with a pipe. It should be noted that the oil tends to overflow, and the pipe should be covered with a rag, and the oil inlet hose should be clamped with a clamp to preve...

How to remove the forklift body and frame? May 08 , 2023

First, the operator seat. 1. Open the battery cover and lock it tightly. 2. Remove the nut from the back of the battery cover of the sit down counterbalance forklift, and then remove the operator's seat. Be careful not to drop the operator's seat during the removal process. Second, the forklift battery cover. Please note that assistance is required when removing the battery cover. When opening or ...

Reasons and Solutions for Heavy Steering of Forklifts Apr 14 , 2023

The reasons and troubleshooting methods of diesel forklift truck turning heavy, shared with you by Xiamen Interquip Machinery Co.,Ltd. Fault phenomenon: When the forklift turns left or right, it feels heavy and laborious to turn the steering wheel. cause of issue: 1. The upper and lower bearings of the steering screw are adjusted too tightly or the bearings are damaged. 2. The adjustment of the me...

How to Check and Adjust The Operating Torque of The Forklift Hand Brake Lever? Mar 17 , 2023

The operating torque can be adjusted as follows to lock the counterbalance forklift truck hand brake lever: 1. Tighten the hand brake lever of the forklift to the locked position. 2. Remove the handle and rubber pad. 3. Use a special tool (KV99107500) to clamp the position of the fork pin, and use the U-shaped notch of the tool to fix the bolt head. 4. Use a special tool (KV99107500) to lock and l...

The Difference Between Lithium Batteries and Lead-acid Batteries for Forklifts Feb 23 , 2023

The Difference Between Lithium Batteries Forklift and Lead-acid Batteries Forklifts 1. The weight of lithium-ion batteries is only 1/4 of that of lead-acid batteries of the same capacity, and the volume is only 1/3 of that of lead-acid batteries of the same capacity. Therefore, under the same power, the mileage that can be driven has increased by more than 20%. 2. After the lithium-ion battery is ...